D-Link DCS-2530L and DCS-2670L Devices Unspecified Vulnerability — D-Link DCS-2530L and DCS-2670L devices contains an unspecified vulnerability that could allow for remote administrator password disclosure. The impacted products could be end-of-life (EoL) and/or end-of-service (EoS). Users should discontinue product utilization.
CVE-2020-25078 is a critical vulnerability (CVSS 9.0) affecting D-Link DCS-2530L and DCS-2670L IP cameras, allowing unauthenticated remote attackers to disclose administrator credentials via a direct request to /config/getuser. This vulnerability enables full device takeover, potential network infiltration, and unauthorized surveillance access. Both devices are End-of-Life/End-of-Service, meaning no further vendor support is expected. Active exploits are publicly available, making this an immediate and high-priority threat for any organization still operating these devices.
IMMEDIATE ACTIONS (0-24 hours):
1. Conduct an asset inventory to identify all DCS-2530L and DCS-2670L devices across your environment.
2. Isolate identified devices from the corporate network immediately — place them on a dedicated, firewalled VLAN with no internet access.
3. Block external access to these devices at the perimeter firewall (deny all inbound traffic to camera management ports 80, 443, 554).
4. Change all administrator passwords on affected devices as a temporary measure.
PATCHING GUIDANCE:
5. D-Link has released firmware patches — apply the latest available firmware immediately if devices are not yet EoL in your region.
6. For confirmed EoL/EoS devices, the vendor recommends discontinuing use — plan immediate hardware replacement with supported alternatives.
7. Replace with supported IP camera models from vendors with active security patch programs.
COMPENSATING CONTROLS (if replacement is delayed):
8. Enforce strict network segmentation — cameras must never share network segments with critical business systems.
9. Implement a reverse proxy or VPN gateway for any required remote access to camera feeds.
10. Disable UPnP on all network devices to prevent automatic port forwarding.
11. Monitor for suspicious access attempts to /config/getuser endpoint in web proxy and firewall logs.
DETECTION RULES:
12. Create IDS/IPS signatures to detect GET requests to '/config/getuser' targeting camera IP ranges.
13. Alert on any authentication attempts or configuration changes on camera management interfaces.
14. Deploy honeypot camera endpoints to detect active scanning for this vulnerability.
الإجراءات الفورية (خلال 0-24 ساعة):
1. إجراء جرد شامل للأصول لتحديد جميع أجهزة DCS-2530L وDCS-2670L في بيئتك.
2. عزل الأجهزة المحددة فوراً عن شبكة الشركة — وضعها في شبكة VLAN مخصصة ومحمية بجدار حماية بدون وصول للإنترنت.
3. حظر الوصول الخارجي لهذه الأجهزة على جدار الحماية الخارجي (رفض جميع حركة المرور الواردة على منافذ إدارة الكاميرا 80 و443 و554).
4. تغيير جميع كلمات مرور المسؤول على الأجهزة المتأثرة كإجراء مؤقت.
إرشادات التصحيح:
5. أصدرت D-Link تحديثات للبرامج الثابتة — قم بتطبيق أحدث إصدار متاح فوراً إذا لم تكن الأجهزة قد وصلت لنهاية دورة حياتها في منطقتك.
6. للأجهزة التي تأكد وصولها لنهاية الدعم، يوصي المورد بإيقاف الاستخدام — خطط لاستبدال الأجهزة فوراً ببدائل مدعومة.
7. الاستبدال بطرازات كاميرات IP مدعومة من موردين لديهم برامج تصحيح أمني نشطة.
ضوابط التعويض (في حالة تأخر الاستبدال):
8. تطبيق تجزئة صارمة للشبكة — يجب ألا تشترك الكاميرات في نفس قطاعات الشبكة مع الأنظمة التجارية الحيوية.
9. تنفيذ بروكسي عكسي أو بوابة VPN لأي وصول عن بُعد مطلوب لتغذيات الكاميرا.
10. تعطيل UPnP على جميع أجهزة الشبكة لمنع إعادة توجيه المنافذ التلقائية.
11. مراقبة محاولات الوصول المشبوهة إلى نقطة النهاية /config/getuser في سجلات البروكسي وجدار الحماية.
قواعد الكشف:
12. إنشاء توقيعات IDS/IPS للكشف عن طلبات GET إلى '/config/getuser' التي تستهدف نطاقات IP للكاميرات.
13. التنبيه على أي محاولات مصادقة أو تغييرات في التكوين على واجهات إدارة الكاميرا.
14. نشر نقاط نهاية كاميرا وهمية للكشف عن عمليات المسح النشطة لهذه الثغرة.